FAAC Hinge & Roller Replacement Nationwide

FAAC Hinge & Roller Replacement: The Pasadena Owner’s Guide

We stock and install FAAC-compatible hinge and roller replacements for swing gates throughout Pasadena, typically between $340 and $680 installed depending on which FAAC series you have and how heavy the gate leaf is. Most hinge and roller swaps happen same-day once we confirm the part geometry on site. What owners usually notice first is a gate that’s started to drag or scrape against the ground on the latch side, or a metallic grind every time the gate cycles.

Call (626) 624-4196

Here’s the part most pages won’t tell you: a FAAC gate rarely fails all at once on this component. The hinge pins wear in a pattern you can see, the nylon rollers flatten into ovals, and the gate slowly loses its geometry over the course of weeks. By the time it’s scraping, the part should have been replaced six months earlier.

Which FAAC Models This Applies To

FAAC builds swing gates under several series lines, and the hinge and roller geometry changes between them. The 412 and 415 operators are the ones we see most on residential gates in Pasadena, and they tend to pair with standard 40-60 mm steel hinges and 80-100 mm track rollers. Larger FAAC 750 and 770 work on heavier commercial leaves, and those use thicker hinge pins and 120 mm rollers. If you still have the FAAC model plate on the operator housing, take a photo before you call us. It saves a trip.

One compatibility gotcha that bites FAAC owners: the hinge centers have to match what’s already welded to the post and the leaf. FAAC doesn’t sell one universal hinge. We carry OEM FAAC hinge sets where they’re still available, plus US-made aftermarket equivalents machined to the same centers. On the roller side, we stock both the standard nylon-bearing rollers and the heavier sealed-bearing rollers that hold up better on gates over 14 feet. For gates near the Arroyo or any property with heavy tree cover, we recommend the sealed version. Debris kills open bearings faster than anything else in this climate.

Note: Vance Gate Repair is an independent service and parts provider. We’re not affiliated with FAAC, and we don’t pretend to be. We carry FAAC-compatible parts because they’re what’s already on your gate, and matching the existing hardware is usually the right call.

Signs Your FAAC Hinge & Roller Replacement Is Failing

• Gate scrapes or drags on the latch side. The bottom hinge has sagged, usually from a worn hinge pin or an egged-out bushing. The leaf drops a quarter inch or more, and the latch side starts kissing the concrete.
• Grinding noise during open or close cycles. A flattened roller no longer rolls; it slides. The flat spot grinds against the track on every cycle. If you run it long enough, it carves a groove into the track itself.
• Gate wobbles side to side when you push it by hand. The roller has worn down to the point where it’s no longer carrying the leaf weight. The gate floats, and the operator arm takes lateral force it wasn’t designed for.
• Gate bounces or shudders near the fully open position. The roller has developed flat spots or the hinge is binding. FAAC operators compensate for resistance until they can’t, and the shudder is the operator fighting the hardware.
• Visible rust streaks below the hinge pins. Water gets into the pin-bearing surface, rust expands, and the pin seizes. On Pasadena’s older iron gates, especially the ones off San Rafael and the surrounding hills, we see this pattern after about six to eight years outdoors.

Before

After

Replacement Cost & What’s Included

For a typical FAAC residential swing gate in Pasadena, hinge and roller replacement runs between $340 and $680 installed, including parts and labor. The spread comes down to gate weight and leaf count: a single lightweight gate on a 10-foot opening sits at the lower end, while a heavy double-leaf gate with sealed-bearing rollers and new hinge pins lands at the top.

Here’s how the price breaks down on a standard single-leaf job:

• Hinge set (two hinges, OEM or US-made equivalent): $90-$180
• Roller assembly (single roller, sealed or standard bearing): $45-$95
• Labor (removal, install, alignment, operator re-check, documentation): $205-$405

Every FAAC hinge and roller replacement we do in Pasadena includes a written price before we unload tools, a photo log of what was found and what went in, and our 365-Day Done Right Promise covering the work for a full year. If the same part fails inside that window because of our install, we come back and make it right. No fee, no argument. If the problem is operator-related, we tell you that and show you the readings.

DIY or Call Us?

You can safely check a few things yourself: push the gate by hand and feel for wobble, look at the roller and see if it’s round or flat-spotted, and hit the hinge pins with a quick visual for rust streaks. That’s diagnosis, not repair.

Where DIY goes wrong on FAAC hinge and roller replacement is the re-alignment. This is a moving assembly that carries significant weight. If your FAAC operator is still connected while you’re replacing a hinge or roller, it can move at any moment. A swing gate that drifts while a hinge pin is half out will shear the remaining fasteners and drop the leaf. We service FAAC hardware in Pasadena for that exact reason: the repair is straightforward for someone who’s done it six hundred times and genuinely dangerous for someone who hasn’t done it once. Call (626) 624-4196, and we’ll photograph everything we find.

FAQs

Need a Written Price? Call Us at (626) 624-4196

If your FAAC gate is dragging, grinding, or wobbling along the track in Pasadena, call Vance Gate Repair at (626) 624-4196. We’ll give you a written price before we touch anything, photograph what we find, and leave you with a complete record of the part numbers and alignment settings. Name what you found. Name what it costs. Leave the gate working. That’s how we do it.

Written by Adrian Vance, Owner, Vance Gate Repair Pasadena at Vance Gate Repair Pasadena, serving Pasadena and nearby areas.