Ghost Controls Gate Parts & Welding Nationwide

Ghost Controls Gate Parts & Welding in Pasadena: What to Know First

We repair Ghost Controls gate hardware and perform the welding work those repairs sometimes require across Pasadena, from hinge replacements to post reconstruction and custom bracket fabrication. Most Ghost Controls parts jobs run between $180 and $650 depending on what failed and whether welding is involved, and we hand you a written price before anyone touches a tool. If you own a Ghost Controls opener or gate and something mechanical has let go, this page tells you what we see most often, what it costs, and how we fix it. Call (626) 624-4196 and a live person answers, any hour.

Call (626) 624-4196

This page is for Pasadena homeowners who already own Ghost Controls equipment and need specific parts or welding work, not a sales pitch for a new opener. We are an independent Ghost Controls service provider, not an authorized dealer, which means we fix what’s on your property rather than steering you toward a replacement you may not need.

How Ghost Controls Products Fail - and How We Fix Them

• Hinge wear on the Ghost Controls heavy-duty swing arm kits (AXS and GHD series). These arms carry real weight on dual-swing gates, and in Pasadena’s dry summer heat the pivot bushings dry out and gall. The gate starts sagging by half an inch, then the motor strains against a misaligned arc. We replace the bearing, ream the hinge bore if it’s ovaled, and weld in a new boss plate when the original hole is wallowed past tolerance.
• Post fatigue at the gate hinge side, especially on the Velo and GTS slide-gate series. A slide gate bounces slightly every time it stops, and over years that vibration works the hinge post loose in its concrete footing. We see it most on Pasadena hillside driveways where the pad wasn’t poured deep enough to begin with. The fix is cutting the post free, setting a new section, welding the hinge brackets at the correct height, and re-anchoring with a deeper footing.
• Weld fractures on the gate frame where the Ghost Controls actuator bracket attaches. The bracket is typically steel, the gate frame is often aluminum or thin-wall tube, and the weld at that junction is a stress concentration point. A fracture there presents as a clicking sound when the opener starts a cycle. We grind out the failed weld, add a reinforcing plate, and re-weld with the correct filler for the base metal.
• Roller and track issues on Ghost Controls slide-gate assemblies. The Velo series uses a cantilever design that’s hard on the guide rollers. When a roller seizes, the gate scrapes and the motor pulls higher amperage until the board faults out. We replace the roller assembly, adjust the track alignment, and photograph the new roller position before we leave.
• Latch and lock misalignment after hinge work on any Ghost Controls swing setup. This is the one that catches owners off guard, because the opener works fine but the gate won’t stay closed against the post. After welding in new hinges or straightening a post, the latch strike is no longer in the right plane. We align the latch, shim or weld the strike plate as needed, and test the full lock-release cycle before the job is done.

Our Ghost Controls Gate Parts & Welding Process

When you call about a Ghost Controls gate problem in Pasadena, here’s what actually happens between the phone call and the final test.

1. 1
   We listen first, then schedule. We ask what the gate is doing, what model you have, and whether the problem is mechanical (hinges, wheels, frame) or electrical (board, motor, sensors). That determines what we load in the truck.
2. 2
   On-site diagnosis with documentation. Our technician examines the gate, identifies the failed component, and photographs everything found. Before any repair work begins, you get a written price for the parts and labor.
3. 3
   Parts decision, spoken plainly. For Ghost Controls jobs, we stock common OEM parts and know which aftermarket equivalents hold up. We tell you which we recommend and why, including the price difference. No surprise substitutions.
4. 4
   The repair or welding work. If the job requires welding, we grind, prep, weld, and clean each joint. If it’s a direct parts replacement, we remove the failed part and install the new one, documenting each step.
5. 5
   Testing and evidence. We run the gate through full open and close cycles, check limit settings, adjust force if needed, and photograph the final result. You receive a photo log and a written record of every part number installed.
6. 6
   The 365-Day Done Right Promise. If the repair isn’t right within one full year, we make it right. No argument, no fee.

Before

After

What Ghost Controls Gate Parts & Welding Costs in Pasadena

We price in writing before work starts. Here are the ranges Pasadena homeowners typically see on Ghost Controls gate parts and welding jobs.

• Hinge replacement (single gate): $180-$320, including new hinge hardware and alignment. Welding in a new boss plate adds $80-$150 if the original hole is worn out.
• Post replacement with welding: $400-$750. This covers cutting out the old post, setting the new one, welding hinge brackets, and re-hanging the gate. Depth of footing and whether the gate is single or double swing moves the price.
• Rail or track repair on a Ghost Controls slide gate: $250-$500 depending on the rail length and whether we weld in a new section or straighten the existing one.
• Custom bracket or frame welding: $150-$400 per bracket. The range reflects how much fabrication is needed and whether the gate metal is steel or aluminum.
• Roller replacement (per roller assembly): $95-$185 including alignment adjustment and testing.
• Latch and lock realignment: $120-$260, including shimming or welding the strike plate to match the new hinge position.

What moves the price: gate weight, whether the post footing is compromised, how much welding fabrication is required, and whether OEM Ghost Controls parts are specified versus high-quality aftermarket equivalents. Every quote includes the parts cost line by line. Call (626) 624-4196 for a free estimate on your specific Ghost Controls repair.

Why Pasadena Homeowners Call Vance Gate Repair Pasadena for Ghost Controls Work

We work on Ghost Controls systems the way Adrian Vance has worked on gates since 2014: name what you found, name what it costs, leave the gate working. Every Ghost Controls parts and welding job in Pasadena comes with a written price before any work begins, a documented photo record when we leave, and a 365-Day Done Right Promise that covers the repair for a full year. Our techs know Ghost Controls limit boards, actuator wiring, and bracket geometry, but we also service LiftMaster, Mighty Mule, DoorKing, and five other major automation brands. That matters when your gate has a Ghost Controls opener mounted on hardware from a different manufacturer, which happens more often than you’d think.

FAQs