Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Farm & ranch
Before
After
Before
After
Before
AfterGate Repair in Burbank, CA
Gate access control in Burbank means working on properties where a studio security desk might sit four blocks from a 1948 rancher with an original wrought iron side gate. The city’s mix of high-cycle commercial gates along the Olive and Alameda corridors and aging residential gates in Magnolia Park and the Rancho means one technician can reset a LiftMaster loop detector in the morning and weld a rusted hinge on a 60-year-old swing gate that afternoon. If your gate won’t open, won’t close, or won’t respond to the keypad, call (626) 624-4196 and we’ll send someone who has worked both kinds of jobs the same week.
Why Burbank Homes Are Different
Burbank’s residential streets are dominated by post-WWII bungalows and ranch homes built between the 1940s and 1960s. That housing stock means gates now 50 to 70 years old: original wrought iron with hinge fatigue at the top pin, rust blooming at ground contact, and operators that were installed when a phone line was still the most advanced access feature a house could have. We see 1990s-era circuit boards with burned relay contacts and no replacement parts available, which changes the repair conversation from “replace the board” to “replace the automation and keep the gate.”
The climate adds another layer. Burbank sits on the San Fernando Valley floor and regularly reaches 105°F in summer, which cooks operator capacitors and degrades wire insulation inside the gate post. Santa Ana winds channeled through the Verdugo foothills put lateral load on gate frames that coastal cities simply don’t experience. A rolling gate that survived a decade in Glendale can be off its track in Burbank after one strong wind event because the guide rollers were never adjusted for that kind of side pressure.
Our Main Burbank Services
Most Burbank homeowners call us first about one of three things: a gate that stopped moving, a gate that needs replacing, or a motor that died years before the gate itself did. Here’s how each works here.
Gate Repair in Burbank
Repair calls in Burbank split roughly evenly between mechanical failures (hinges, tracks, sagging frames) and automation failures (boards, limit switches, remote receivers). The older housing stock means we often repair a gate that’s outlasted two operators. Full details on what we fix and what it costs are on the Gate Repair in Burbank page.
Gate Installation in Burbank
New gate installations here usually mean working within an existing driveway footprint, often with a 1950s concrete pad that needs a welded frame sized around it rather than a fresh pour. We handle the measurements, the written scope, and the install. See Gate Installation in Burbank for the full breakdown and local pricing.
Gate Motor & Opener in Burbank
When the operator fails on a Burbank gate, the decision is whether the motor is worth replacing on its own or whether the whole automation package needs to go. Heat damage and Santa Ana strain mean some operators aren’t worth reviving. The Gate Motor & Opener in Burbank page covers replacement costs and what we check before recommending anything.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Burbank
Burbank’s gate access control work is shaped by the city’s unusual split: residential keypads and phone entry on Magnolia Park and Rancho homes with entertainment-industry owners who expect commercial-grade reliability, and studio-adjacent properties where the access system runs hundreds of cycles a day. A keypad that works fine in Porter Ranch fails faster here because the summer heat inside the housing shortens capacitor life. We service LiftMaster and FAAC access panels, wire new keypads, and integrate existing Gate Access Control components without pushing a full replacement unless the board is genuinely obsolete.
Keypad Entry
Signs you need it
You’re entering a code multiple times before the gate responds, or the keypad works only when pressed hard.
What it costs in Burbank
Keypad replacement or new installation in Burbank typically runs $180 to $420 depending on whether we’re wiring a new unit or swapping an existing one.
How we do it
We test the existing keypad’s output at the board, verify the wiring, swap the unit if needed, and photograph the new programming before we leave.
Phone Entry
Signs you need it
Callers get no ring at the house, or the gate opens only when the same number is called twice.
What it costs in Burbank
Phone entry system installation in Burbank generally lands between $350 and $800, depending on whether we’re programming an existing cellular unit or mounting new hardware.
How we do it
We check the SIM or phone-line connection, confirm the relay fires at the gate board, and reprogram the directory so the call routes to the right line every time.
What Gate Access Control Costs in Burbank
| Item | Typical range in Burbank |
|---|---|
| Keypad replacement | $180 - $420 |
| Phone entry system | $350 - $800 |
| Card reader or video intercom integration | $400 - $1,200 |
Can you integrate access control with a gate that’s already automated?
Yes. We wire keypads, card readers, and phone entry into existing LiftMaster, FAAC, or BFT operators as long as the board has an open input. The written quote lists exactly which components we’re adding and what we’re programming.
Does Burbank require permits for residential gate access control work?
Low-voltage access control wiring on an existing gate typically doesn’t need a permit in Burbank, but we confirm any HOA or studio-adjacent requirements before starting. Call for a straight answer on your specific property.
Gate Parts & Welding in Burbank
Burbank’s 1940s and 1950s gates weren’t built with replaceable parts in mind, so when a hinge fails or a post rusts through, the fix is often welding and fabrication rather than an off-the-shelf swap. The heat and Santa Ana wind cycles mean we see more ground-contact rust and more frame cracks here than in coastal cities. Our Gate Parts & Welding work covers hinge replacement, post repair, rail straightening, and custom bracket fabrication, all done on site with a written price before the welder fires.
Hinge Replacement
Signs you need it
The gate sags at the latch side, scrapes the ground, or the top hinge pin shows visible wear when the gate swings.
What it costs in Burbank
Hinge replacement on a Burbank gate typically runs $120 to $450 per hinge, depending on whether the post needs reinforcement too.
How we do it
We cut or unbolt the old hinge, weld or bolt the new one in place, align the gate, and photograph the finished weld and the gate’s operating clearance.
Post Replacement
Signs you need it
The post leans, shows rust-through at the base, or moves when the gate opens and closes.
What it costs in Burbank
Post replacement in Burbank generally runs $500 to $1,500 including digging, new post, concrete, and re-hanging the gate.
How we do it
We remove the old post, set a new steel post in concrete, brace it level, and re-hang the gate once the concrete has cured to strength.
What Gate Parts & Welding Costs in Burbank
| Item | Typical range in Burbank |
|---|---|
| Hinge replacement | $120 - $450 per hinge |
| Post replacement | $500 - $1,500 |
| Custom welding or frame repair | $200 - $900 |
Can you weld my existing gate rather than replace it?
Usually, yes. If the steel is thick enough to take a clean weld, we repair the frame in place. If the gate is too far gone at the ground-contact points, we’ll say so in writing before recommending a replacement.
How soon can you get parts for an older Burbank gate?
Common hinges, rollers, and brackets are stocked on our trucks. For odd-size or vintage parts, we fabricate on site or order with a 2 to 4 day turnaround. The written quote covers either path before work starts.
Brands We Service in Burbank
We work on whatever motor is already on the property. Our Burbank trucks carry parts for LiftMaster, FAAC, BFT, and Linear operators, which covers most of what’s installed across the city’s residential and studio-adjacent gates. See our brands page for the full list of what we service.
Pricing for Gate Repair in Burbank, CA
| Service | Typical range in Burbank |
|---|---|
| Keypad replacement | $180 - $420 |
| Phone entry system | $350 - $800 |
| Card reader or video intercom integration | $400 - $1,200 |
| Hinge replacement | $120 - $450 per hinge |
| Post replacement | $500 - $1,500 |
| Custom welding or frame repair | $200 - $900 |
| Gate motor replacement | $650 - $1,800 |
| Full gate installation | $1,800 - $6,500 |
Two things push prices higher in Burbank than in neighboring cities: the summer heat damage to circuit boards and capacitors, and the wind-related frame stress that turns a simple hinge job into a post reinforcement. Whatever the total, the price is written and handed to you before any work starts, and it’s the price you pay.
Neighborhoods We Serve in Burbank
We cover the whole city, from the hillside lots above Kenneth Road to the flat streets of the Rancho. Response time for non-emergency calls in Burbank is usually same day or next morning, depending on the schedule.
- Magnolia Park
- The Rancho
- Burbank Hillside
- Toluca Terrace adjacent
- North Burbank
Service Area - Cities Near Burbank
Our crews serve Burbank and the surrounding San Fernando Valley and foothill communities. We also work across the line in North Hollywood, CA, Sun Valley, CA, Tujunga, CA, and Altadena, CA, so if your gate sits near the city line, call and we’ll route the nearest truck.
Serving Burbank, CA - Our Local Coverage Area
We’re based in the Burbank area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Burbank
For gate failures that leave a property unsecured or a gate stuck open, we dispatch same day in Burbank. A live person answers the phone 24 hours a day at (626) 624-4196, and we’ll tell you when a technician can be there before you hang up.
Most residential gate repairs on existing structures don’t require a Burbank building permit. If your home is in an HOA with architectural rules, we’ll work from whatever approval you already have, and the written quote notes any HOA-specific requirements we observed.
Burbank’s summer heat, which regularly exceeds 100°F, degrades operator circuit boards and capacitors faster than in cooler parts of Los Angeles. Santa Ana wind events also stress gate frames and knock rolling gates off track, which then overloads the motor. Our service includes heat-related component checks as standard.
For a written quote on any gate repair in Burbank, call (626) 624-4196. We’ll name the price before we start, and we’ll leave you with a photo record of what we did.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Burbank Customers Say
"Quoted in writing, installed on the day promised, and the price did not move. The crew was licensed and the number was on the paperwork."
- Wes A."The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H."Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B.